site logo

ການ​ແກ້​ໄຂ​ບັນ​ຫາ​ວົງ​ຈອນ​ພາຍ​ໃນ​ຂອງ slicer mutton​

Solutions to the internal circuit problems of the ເຄື່ອງຕັດຊີ້ນງົວ

1. ຕັດສາຍເຫຼັກວ່າງຢູ່ສາຍທີ່ຫັກອອກກ່ອນ, ແລະປະໄວ້ສອງສາຍເຫຼັກຍາວກວ່າໄລຍະຫ່າງລະຫວ່າງລໍ້ຄູ່ມື 10 ຊມ.

2. ໃຊ້ກະດາດກະດາດຫຍາບຂັດເສັ້ນຜ່າກາງຂອງສອງສົ້ນຂອງສາຍເຫຼັກເປັນ 1/2-2/3 ຂອງສາຍເຫຼັກຂອງເຄື່ອງຕັດ mutton ຕົ້ນສະບັບ, ແລະຄວາມຍາວຄວນຈະຫຼາຍກ່ວາ 5 ຊຕມ. ໃຊ້ກະດາດຊາຍລະອຽດເພື່ອເຮັດໃຫ້ພື້ນຜິວຂອງສາຍເຫຼັກລຽບ, ແລ້ວໃຊ້ມັນອີກເທື່ອຫນຶ່ງ. ລ້າງສາຍເຫຼັກສອງເສັ້ນຈົບດ້ວຍເຫຼົ້າ.

3. The two steel wire ends with 5 cm sand removed are overlapped and welded together. Use an electric soldering iron to weld one end of the steel wire homeopathically. The two steel wire ends must be completely overlapped and the steel wire cannot be warped. When I get up, I can only re-solder, and then use fine sandpaper to smooth the welding place and wash it with alcohol.

4. There must be a long section of the steel wire that is loose, and run the loose section to the guide rail of the mutton slicer.

5. ແບ່ງຄວາມຍາວຂອງເສັ້ນລວດຈາກທ້າຍຂອງລໍ້ຄູ່ມືໂດຍຊ່ອງສຽບຂອງລໍ້ຄູ່ມືແລະຄູນມັນດ້ວຍຄວາມຍາວຂອງຫນຶ່ງລ້ຽວຂອງລໍ້ແນະນໍາສາຍເຫຼັກ.

6. Accelerate every second until the speed reaches normal, and then cut.

ຖ້າມີບັນຫາວົງຈອນພາຍໃນກັບເຄື່ອງຕັດຊີ້ນ, ທໍາອິດໃຫ້ຕັດການສະຫນອງພະລັງງານແລະກວດເບິ່ງວ່າສາຍແມ່ນຕິດຕໍ່ໄດ້ດີ. ທ່ານ​ສາ​ມາດ​ແກ້​ໄຂ​ມັນ​ໄດ້​ຕາມ​ວິ​ທີ​ການ​ຂ້າງ​ເທິງ​ນີ້​ເພື່ອ​ເຮັດ​ໃຫ້​ການ slicer ແລ່ນ​ກ້ຽງ​.

ການ​ແກ້​ໄຂ​ບັນ​ຫາ​ວົງ​ຈອນ​ພາຍ​ໃນ​ຂອງ slicer mutton​-ເຄື່ອງຊອຍຊີ້ນແກະ, ເຄື່ອງຕັດຊີ້ນງົວ, ເຄື່ອງຕັດເຊືອກລູກແກະ / ແກະ, ເຄື່ອງຕັດເຊືອກໃສ່ຊີ້ນງົວ, ເຄື່ອງຕັດຜັກຫຼາຍປະການ, ເຄື່ອງຫຸ້ມຫໍ່ອາຫານ, ໂຮງງານຜະລິດຈາກປະເທດຈີນ, ຜູ້ຜະລິດ, ຜູ້ຜະລິດ, ຂາຍສົ່ງ